The BougeRV 200W CIGS Adhesive Kit is a 200-watt cigs thin-film option best suited to complete drill-free structural install. Drill-free kit with inverter + LFP battery.
Overview
A single-panel 200W CIGS kit for the lightest possible rooftop install: the Yuma thin-film panel bonds on with adhesive tape — no holes, no penetrations — which is exactly what a thin manufactured-home or van roof calls for.
It comes with a 30A MPPT controller, a 12V 100Ah LiFePO4 battery, and a 2,000W pure sine wave inverter, so a first-timer gets a complete drill-free system in one box.
Features & real-world use
The most flexible panel in the kit
The CIGS sheet bends a full 360° and is glass-free, so it wraps curves that crack a rigid 'flexible' mono panel at 30°.
Built to outlast a mono array
CIGS holds nearly all its rated output after years of mobile use, where a comparable mono panel degrades or gets scrapped in 1–3 years — closer to $10 a year than $50.
IP68 waterproof, rain or snow
The panel, connectors, and junction box are sealed to IP68 and rated to 2400Pa wind and 5400Pa snow load, so weather on the roof doesn't faze it.
Bypass diodes keep the power steady
The panel's 24 bypass diodes keep it producing when part of it falls into shade, where cheaper panels with only two diodes stop delivering.
Light enough to handle solo
The panel weighs about 7 lbs and ships with MC4 leads and a sealed cable box, so one person can peel, stick, and wire it.
Built for any roof, deck, or vehicle
The single CIGS panel bonds on with adhesive tape and flexes to 360°, so it goes onto almost any roof or deck a rigid module can't — while the 30A controller, LiFePO4 battery, and 2,000W inverter make it a complete drill-free system.
RV & trailer roofs
The adhesive panel bonds flush to fiberglass, aluminum, or rubber and follows the roof's crown — no rack, no penetrations to seal.
Camper vans & conversions
One low-profile panel for a high-top or pop-top roof, with the power system mounted inside.
Boats & marine decks
IP68 sealing and 2400Pa/5400Pa ratings suit a wet, exposed deck.
Airstreams & curved rigs
360° flex wraps the tight radius of a polished trailer where a rigid panel can't sit.
Mobile & manufactured homes
A single adhesive panel adds almost nothing to a thin HUD-code roof's dead-load budget while the LiFePO4 bank runs real loads.
Cabins, sheds & tiny homes
A complete drill-free off-grid starter system for an outbuilding.
What's in the box
- 1 × Yuma 200W CIGS thin-film flexible panel (adhesive tape)
- 1 × 30A MPPT solar charge controller
- 1 × 12V 100Ah LiFePO4 battery
- 1 × 2,000W 12V pure sine wave inverter
Specifications
| Brand | BougeRV |
|---|---|
| Category | DIY Solar Kits |
| Power output | 200 W |
| Cell technology | CIGS Thin-Film |
| Price | $999.99 |
| Best for | Complete drill-free structural install |
| Charge Controller | 30A MPPT |
| Inverter | 2,000W |
| Battery | 100Ah LiFePO4 |
Roof-load fit for manufactured homes
CIGS thin-film adds under 0.5 psf and bonds flat to the deck — no point loads, safe across all HUD roof-load zones (South, Middle, North).
This kit ships with a battery — here's how the two common off-grid chemistries compare:
Pros & cons
👍 Pros
- Flexible CIGS thin-film — drill-free, zero point-load on the roof
- Includes an efficient MPPT charge controller (95–98% vs ~75% PWM)
👎 Cons
- Lower peak efficiency than premium rigid mono — needs more area per watt
Is the BougeRV 200W CIGS Adhesive Kit right for your mobile home?
Choose this panel if your priority is complete drill-free structural install. Because it is a flexible, low-profile panel, it can usually go straight onto a manufactured roof without exceeding the 10–15 psf dead-load limit. For full sizing math, HUD roof-load zones, and permitting requirements, read our complete buyer's guide.
Reviews
No reviews yet. Bought this panel? Be the first to review it — your experience helps other mobile-home owners choose.
